LinuxDevCenter.com
oreilly.comSafari Books Online.Conferences.

advertisement


Speeding up Linux Using hdparm

by Rob Flickenger
06/29/2000

Are you running an Intel Linux system with at least one (E)IDE hard drive?

Wouldn't it be neat if there were a magical command to instantly double the I/O performance of your disks? Or, in some cases, show 6 to 10 times your existing throughput?

Did you ever just wonder how to tell what kind of performance you're getting on your "tricked-out" Linux box?

Don't overlook hdparm(8). If you've never heard of it, don't worry. Most people I've talked to haven't either. But if you're running an IDE/Linux system (as many folks are,) you'll wonder how you ever got this far without it. I know I did.

What's the big deal?

So, you've got your brand-new UltraATA/66 EIDE drive with a screaming brand-new controller chipset that supports multiple PIO modes and DMA and the leather seat option and extra chrome... But is your system actually taking advantage of these snazzy features? The hdparm(8) command will not only tell you how your drives are performing, but will let you tweak them out to your heart's content.

Now before you get too excited, it is worth pointing out that under some circumstances, these commands CAN CAUSE UNEXPECTED DATA CORRUPTION! Use them at your own risk! At the very least, back up your box and bring it down to single-user mode before proceeding.

With the usual disclaimer out of the way, I'd like to point out that if you are using current hardware (i.e. your drive AND controller AND motherboard were manufactured in the last two or three years), you are at considerably lower risk. I've used these commands on several boxes with various hardware configurations, and the worst I've seen happen is the occasional hang, with no data problems on reboot. And no matter how much you might whine at me and the world in general for your personal misfortune, we all know who is ultimately responsible for the well-being of YOUR box: YOU ARE. Caveat Fair Reader.

Now, then. If I haven't scared you away yet, try this (as root, preferably in single-user mode):

hdparm -Tt /dev/hda

You'll see something like:

/dev/hda:
 Timing buffer-cache reads:   128 MB in  1.34 seconds =95.52 MB/sec
 Timing buffered disk reads:  64 MB in 17.86 seconds = 3.58 MB/sec

What does this tell us? The -T means to test the cache system (i.e., the memory, CPU, and buffer cache). The -t means to report stats on the disk in question, reading data not in the cache. The two together, run a couple of times in a row in single-user mode, will give you an idea of the performance of your disk I/O system. (These are actual numbers from a PII/350 / 128M Ram / newish EIDE HD; your numbers will vary.)

But even with varying numbers, 3.58 MB/sec is PATHETIC for the above hardware. I thought the ad for the HD said something about 66MB per second!!?!? What gives?

Well, let's find out more about how Linux is addressing your drive:

hdparm /dev/hda

/dev/hda:
 multcount    =  0 (off)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 1870/255/63, sectors = 30043440, start = 0

These are the defaults. Nice, safe, but not necessarily optimal. What's all this about 16-bit mode? I thought that went out with the 386! And why are most of the other options turned off?

Well, it's generally considered a good idea for any self-respecting distribution to install itself in the kewlest, slickest, but SAFEST way it possibly can. The above settings are virtually guaranteed to work on any hardware you might throw at it. But since we know we're throwing something more than a dusty, 8-year-old, 16-bit multi-IO card at it, let's talk about the interesting options:

  • multcount: Short for multiple sector count. This controls how many sectors are fetched from the disk in a single I/O interrupt. Almost all modern IDE drives support this. The man page claims:

    When this feature is enabled, it typically reduces operating system overhead for disk I/O by 30-50%. On many systems, it also provides increased data throughput of anywhere from 5% to 50%.
  • I/O support: This is a big one. This flag controls how data is passed from the PCI bus to the controller. Almost all modern controller chipsets support mode 3, or 32-bit mode w/sync. Some even support 32-bit async. Turning this on will almost certainly double your throughput (see below.)


  • unmaskirq: Turning this on will allow Linux to unmask other interrupts while processing a disk interrupt. What does that mean? It lets Linux attend to other interrupt-related tasks (i.e., network traffic) while waiting for your disk to return with the data it asked for. It should improve overall system response time, but be warned: Not all hardware configurations will be able to handle it. See the manpage.


  • using_dma: DMA can be a tricky business. If you can get your controller and drive using a DMA mode, do it. But I have seen more than one machine hang while playing with this option. Again, see the manpage (and the example on the next page)!

Pages: 1, 2

Next Pagearrow




Linux Online Certification

Linux/Unix System Administration Certificate Series
Linux/Unix System Administration Certificate Series — This course series targets both beginning and intermediate Linux/Unix users who want to acquire advanced system administration skills, and to back those skills up with a Certificate from the University of Illinois Office of Continuing Education.

Enroll today!


Linux Resources
  • Linux Online
  • The Linux FAQ
  • linux.java.net
  • Linux Kernel Archives
  • Kernel Traffic
  • DistroWatch.com


  • Sponsored by: